Will not work on a Husqvarna T435.
Showing questions 1 - 9 of 9
Page:
1
|
| Q. |
Can I use this on my 075 to replace my clutch?
|
| A. |
Yes, it works on any saw/two stroke engine that takes the standard size spark plug.
|
| |
335 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Tom A from NY on 6/12/2008 |
|
| |
| Q. |
Will this device damage the piston head if you use it a lot? Cause we strip down our saws every day and clean them, we use starter rope, but this looks like a better tool cause some times the piston will cut the rope then you have to fish out the cut end. But it just seems like the pressure from cranking the clutch off would dent up the piston head.
|
| A. |
Piston stops are not recommended, or needed, with an air wrench. When using standard wrench with a piston stop it can leave a small mark on the top of the piston which does no harm. Using a rope can actually do more damage if it doesn't hold and the crank turns over as there will be a tremendous inc
...
(See full answer)
Piston stops are not recommended, or needed, with an air wrench. When using standard wrench with a piston stop it can leave a small mark on the top of the piston which does no harm. Using a rope can actually do more damage if it doesn't hold and the crank turns over as there will be a tremendous increase in pressure on the bearings as the piston goes over the top dead center. This will cause harm to the saw. (Hide full answer) |
| |
289 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: fire f from ca on 7/5/2008 |
|
| |
| Q. |
This tool appears to have sharp corners at the contact end. Is the picture not accurate or is this the actual shape of the contact head?
|
| A. |
The photo is accurate. Please see previous FAQ's for more info.
|
| |
356 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: KJM T from WA on 10/18/2008 |
|
| |
| Q. |
Is this tool supposed to contact piston face only in a vertical orientation thereby having its flat end flush with the piston face surface?
|
| A. |
No, the edge hits the top of the piston.
|
| |
282 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: kyle m from ky on 4/22/2009 |
|
| |
| Q. |
I have a question regarding the replacement of the clutch. What is the proper torque for the clutch?
|
| A. |
Greetings - The torque depends on the chainsaw model. One of our mechanics will contact you via email to assist you further.
|
| |
229 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Russell from Fl on 11/13/2009 |
|
| |
| Q. |
On a Husky 51, what direction should I be turning the cluch assembly to remove it?
|
| A. |
Greetings- You should be turning it clockwise for removal. Thank you for the inquiry.
|
| |
206 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Thom H from MO on 11/20/2009 |
|
| |
| Q. |
Of the available piston stops sold by Bailey's, which would work best with a Husqvarna 455 Rancher?
|
| A. |
Greetings - We recommend this piston stop for any saw on the market, including the 455. Thank you for the inquiry.
|
| |
223 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: JD from IN on 11/21/2009 |
|
| |
| Q. |
what thread pitch does the spark plug part useand will it fit my poulan pro 260?
|
| A. |
Thread pitch is the same for all spark plugs too 14mm x 1.25mm - Yes it will work on our saw.
|
| |
177 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: bobby a from mi on 3/7/2010 |
|
| |
| Q. |
What is the torque when installing the clutch on Husqvarna 61? I assume it is left hand thread as well.
|
| A. |
35 NM
|
| |
173 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Nick R from PA on 3/11/2010 |
|
| |
Showing questions 1 - 9 of 9
Page:
1
|
Showing reviews 1 - 1 of 1
Page:
1
|
|
Piston Stop
|
|
Posted by: Brian D from IL on 8/25/2009
|
Rating: 
|
|
Piston stop works great. The picture on the website looks like there is a square edge on the stem that contacts the piston, but the actual item has a beveled edge where it contacts the piston.
Used the piston stop on 3 different saws today, works great! Get yourself one!
|
|
225 people found this review helpful.
|
|
Was this review helpful?
Yes
|
| |
|
Showing reviews 1 - 1 of 1
Page:
1
|
|
