| Q. |
Hi, I'm looking for a spur sprocket or rim & drum system for a Dolmar PS-420to run 1/4" carving chains, I wasn't able to find anything on your website.ThanksRolf
|
| A. |
Sorry, there is no 1/4 pitch drive sprocket or a rum and drum for that machine as of yet.
|
| |
38 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: ROLF K from NS on 12/29/2011 |
|
| |
| Q. |
will this fit my 015av stihl with 1/4 pitch. Does it slip over my current 8 spur sprocket? also do you have rim for an 029 super with .325 pitch/.063 gauge?does it change the drive link countThanksBruce
|
| A. |
On the Stihl 015 you won't be able to put this rim on your spur sprocket. It is intended only for a change on a rim and drum system. At this time we don't carry a rim and drum for that saw, nor have access to a 1/4 pitch sprocket for the 015.
For the Stihl 029 it takes a small spline ORF 11892. Onl
...
(See full answer)
On the Stihl 015 you won't be able to put this rim on your spur sprocket. It is intended only for a change on a rim and drum system. At this time we don't carry a rim and drum for that saw, nor have access to a 1/4 pitch sprocket for the 015.
For the Stihl 029 it takes a small spline ORF 11892. Only the pitch matters on the spline and not the gauge. So you are in the clear on that matter. If you keep with the standard 7 tooth on the spline, you can suit up your .325 x .063 bar with the same drive link count you have been using. (Hide full answer) |
| |
27 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: BRUCE W from MD on 2/21/2012 |
|
| |
| Q. |
Will this sprocket work on the Husqvarna 254 XP
|
| A. |
Yes, if your Serial Number is after 345-0001. You can check the inside diameter of your existing spline to triple check and see if it is about 3/4".
|
| |
25 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: JYRI L from FN on 3/29/2012 |
|
| |
| Q. |
Hi, will this rim sprocket fit a husky 339xp
|
| A. |
No it won't fit. The 339 tends to have a spur and this is for a rim and drum.
|
| |
24 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: MIKE W from BC on 5/26/2012 |
|
| |
| Q. |
Say, you can use 1/4 "Pitch Rim Sprocket for Husqvarna 560XP chainsaw with Cannon Carving Bar Quarter?
|
| A. |
In checking what size comes stock on your Husqvarna 560XP they show both the large and small spline. Measure your spline and see if it is 3/4 ID. If so, your saw can accept the CSR 14 spline.
|
| |
17 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: ALEXSANDR K from FN on 10/11/2012 |
|
| |
| Q. |
I have a 435 Husqvarna, can I find a carving kit for it?
|
| A. |
CK12 340 should do the trick.
|
| |
21 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: RICHARD F from MT on 12/22/2012 |
|
| |
