| Q. |
Dear Sir: The question is, will this tachometer work with my 1/3 hp electric motor. Thank you. Torres
|
| A. |
Sorry, it wouldn't work for that purpose because it counts sparks. Sendec is the manufacturer. They do make a tach that use a target that can be attatched to any rotating shaft.
|
| |
414 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: jose l from canada on 12/1/2007 |
|
| |
| Q. |
How is it powered? Battery? Is it replaceable? What kind of battery? Thanks
|
| A. |
It's battery powered. The battery is not replaceable. We've had a couple in our shop for 8 - 10 years with no issues.
|
| |
375 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: John U from PA on 1/23/2008 |
|
| |
| Q. |
Will this Tach work on 1 cyl. small engines ? What about 2 strokes ?
|
| A. |
Yes, it will.
|
| |
327 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Paul 4 from MA on 1/24/2008 |
|
| |
| Q. |
Dear Sir, Will This work on 2 or 4 cycle engines and 1 to 2 cylinders Thanks Les
|
| A. |
Yes, it will work on 2 or 4 cycle, and one or 2 cylinder engines. There are settings to adjust for the # of cylinders.
|
| |
384 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Les from Ca on 4/1/2008 |
|
| |
| Q. |
How do you hook up the SenDec STS-5000 Shop Tachometer and will it work on 2 cycle(4cyl) OUTBOARD engines?
|
| A. |
It's made for 2 cycle, and 4 cycle. Single, and twin cylinder engines. These tachs read sparks. So with some math, you can calculate the rpm's for anything that produces a spark. It can either be held close to the spark plug, or use the included wire and clip to hook directly to the spark plug wire.
|
| |
361 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: John G from Palmetto,FL on 8/26/2008 |
|
| |
| Q. |
Will this tach work with the newer saws? I have a Stihl MS660 bought earlier this year and a Husqvarna 357XP from 2003 and Stihl MS210. Thanks
|
| A. |
Yes, it will work on your saws.
|
| |
356 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Robert M from PA on 10/31/2008 |
|
| |
| Q. |
Is this the best tach for setting up my 372xp's Carb? I want to use it to make sure I'm not exceeding 13,800 rpms. Thank you.
|
| A. |
This is the brand we've always used. They are a very good unit.
|
| |
348 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Chad H from Ohio on 1/5/2009 |
|
| |
| Q. |
How long is the lead going to the spark plug?
|
| A. |
Apprx. 18"
|
| |
209 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Raymond K from EriePa. on 3/3/2010 |
|
| |
| Q. |
I would like to purchase your Tach. You mentioned it would work with 4 stroke, 2 cylinders. You also mentioned that some math would be involved. Are the formulas included in the manual? Where would I find the proper math formula? I wish to use this tach to set proper RPM idle speeds on motorcycles.
|
| A. |
For two and four cylinder engines there is a mode button you set on it and it reads the radio signal from your plugs.
|
| |
213 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Jake K from York on 3/3/2010 |
|
| |
| Q. |
Can you tell me if this tach can be used without wires?
|
| A. |
Yes, you can use it without wires.
|
| |
219 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Steve from PA on 3/18/2010 |
|
| |
