| Q. |
What 1/4" carving sprockets, bars and chains do you have for Craftsman 34117, 34118 @ Mccullouch mcc4516? Thanks.
|
| A. |
We don't have anything for the Mac. I need more of the model number off of the Sears saws. Most of the Sears saws were made by Poulan. We might be able to cross reference them with more model number information.
|
| |
353 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: niall m from ga on 1/6/2008 |
|
| |
| Q. |
Good morning! Would you have a small spline config. rim drum that would work on small Homelites like the XL, XL2 and Super 2? Thanks!Joe
|
| A. |
Sorry, all we have is spur sprockets.
|
| |
295 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Joe from MO on 1/25/2008 |
|
| |
| Q. |
I'm a ice carver and I'm looking to change my chainsaw bar to a carving bar. I have a Stihl mse180 16" bar. drive link count of 55, pitch =3/8" Picco. What can I do to change my Stihl chainsaw to be able to use a carving bar (dime, quarter size tip)?
|
| A. |
What you need is a CRD S8N. Plus a bar and chain.
|
| |
338 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: terrence h from mo on 1/29/2008 |
|
| |
| Q. |
What is a CRD S8N and do you sell them? Thanks Terrence
|
| A. |
Put CRD S8N in the search box on our home page.
|
| |
263 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: terrence h from mo on 1/29/2008 |
|
| |
| Q. |
Will this fit a 460 Magnum, and does it have 7 drivers?
|
| A. |
It is a 9 tooth with a 3/4" ID. Your 460 has the 7/8" ID so it will not fit.
|
| |
254 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: ben t from illinois on 1/30/2009 |
|
| |
| Q. |
Would this fit the rim drive on a Homelite Super EZ? Thanks.
|
| A. |
It should. The ID of the rim is 3/4".
|
| |
256 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Jared D from IA on 2/11/2009 |
|
| |
| Q. |
Will this sprocket work on the Stihl MS260 Pro?
|
| A. |
Yes it will.
|
| |
201 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: Brad W from Kansas on 9/29/2009 |
|
| |
| Q. |
what is the tooth count on this sprocket?
|
| A. |
9
|
| |
145 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: KEVIN A from CA on 6/17/2011 |
|
| |
| Q. |
Is this the "Small 7 Spine (SM 7)" size ID as referred to in the Oregon Power Mate System?
|
| A. |
Yes, SM but is 9 tooth to allow for the 1/4 pitch teeth configuration..
|
| |
150 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: KEVIN A from CA on 6/17/2011 |
|
| |
| Q. |
Will this fit the Husqvarna 142 and 235? Do I also need to change the bearings and drum if the originals are still in good shape?
|
| A. |
If you are currently running a rim and drum drive system converting to 1/4 pitch application is simply slipping the existing rim off and this one on. Since the existing bearing and drum is fine, you should be good to go. Grease that bearing fresh through.
|
| |
109 people found this answer helpful.
|
| |
Was this question helpful?
Yes
|
| |
Posted by: MARK F from MN on 11/30/2011 |
|
| |
