21. February 2013 23:41
Finally got back up to the cabin after break-up, everything looked good with the exception of a few visits from Mr. Black Bear. Bear got in and decided a couple of ventilation holes need to be added to the inside surface of the house wrap behind the siding. Only pocked 4 small holes in it that can easily be fixed with scrap pieces and tape, he also decided to take a taste from an edge of one of the clap siding boards but only a small taste. Siding looked good with no cracks from drying, even on the south wall. All of the vertical post have vertical splits in them but I figured they would check out as they dried like log houses do. Hauled the canoe up in my boat and left it at the lake for future use (a small canoe trip is needed from the main river to get to the cabin). Foundation still seems level, plan on bringing up the laser level next trip to check if there was any settling. Planning on hauling up windows and insulation when it gets in on the barge. Looking forward to milling lumber again for trimming out the windows. Will post more photos in the next couple of weeks. Maybe black bear sausage as well!
Approaching cabin in canoe from the south.
Cabin south wall.
View from cabin looking east.
14. February 2013 17:20
Got the metal on, getting things wrapped up and put away for break up. Will start working on it again in June when I can travel up by boat.
View from lake
Front of cabin
Another shot from the lake
View from main snogo trail
9 year old son Koby heading home on his Bravo
Will post more pics in June, hoping the black bears don't tear things up too bad between now and then, they will probably have fun with the house wrap on the inside.
Be sure to check back next Thursday for Part 20!
31. January 2013 22:54
1x6 skip boards in place
Eave and Gable trim in place and all ready for metal.
Plan on putting metal in place on Sunday.
Snow melting on trail in front of Cabin, got in the 50's in the afternoon.
Pulled mill of the ice so it doesn't become an anchor, put it in the cabin for the summer work after break up.
Snow melting around the arctic oven, hoping to get one more weekend to get things done until June.
Be sure to check back next Thursday for Part 19!
25. January 2013 00:22
Cabin Building 4/13/11
Haven't put up pics for a couple of weeks because I can't remember to bring my camera. Got all but one of the trusses done last weekend, only have one more to make in the jig. Have them up on the top plates ready for 1x skip sheeting before putting on the metal roof.
Started moving slabs of the ice and stacking them for next years fire wood. Spring is on the way, maybe 2 or 3 weekends left before traveling by snowmachine will not be possible. Great days for building now with daylight hours from 7 am to 11 pm.
Be sure to check back next Thursday for Part 17!
10. January 2013 20:01
Worked on putting siding on this weekend.
House wrap installed and siding story board marks made on wall.
South wall left side done.
Right courses done up to top of window.
South wall finished with siding.
Be sure to check back next Thursday for Part 16!
3. January 2013 19:37
Cabin Building Day 14
Got a couple more logs cut down ready for making siding and put the double top plates in place. Squared up the walls and braced them, ready to install house wrap and siding next weekend.
24" Big Daddy Spruce, hope that 20" chain from Baileys comes in for this one, been on order for 2 months now, should be in this week.
Top Plates installed
View from above
20. December 2012 18:50
Cabin Building Day 12
It finally warmed up in interior Alaska
Got the second long wall done with the window openings. One more wall to go.
End view, planning on getting the last wall with door and window done on Sunday.
Loaded up the big spruce to cut some 2x4's
Big spruce with log lifts bottomed out, just able to take a small slice with the 20" bar, to big for the 16" bar.
Had to use a standard stihl chain and standard 20" bar, ordered a 20" bar and low pro rip chain from Bailey's but it has not come in yet.
For those who are wondering how the mill cuts with standard cross cut chain, it really slow and makes some big chips (lots of them)! Rip chain is way faster!
Really did not have a choice, was able to take off 4 slabs and get the log down to a 14" square cant to cut with the 16" low pro rip chain and bar.
14" cant is the max for my 16" bar, cut two 4x14" cants from center then rip the both at the same time into 2x4's, nice getting 2 stud boards with each pass.
Was able to yield 15 true 2x4's and one 1x14" from the large spruce.
13. December 2012 23:40
Cabin Building Day 11
After not being able to go out for two weeks (temps in the -40's F) on the weekend, finally got out this weekend. Two plus feet of fresh snow so I spend most of my time digging things out and getting stuck pulling logs to the mill. Was able to get the rest of the wall beams cut and some of the walls studs for the last two walls. Planning on getting the walls finished up next weekend if its not -40!
Logging in 4' of snow, mad felling skills on the right tree, should have been a field goal kicker J
1st tree loaded up ready to head to the mill, got stuck 12 times on the way (1/4 mile), with a 24" superwide track!!!! If its not -40 its 4' of powder. Warn winch got its workout today.
Snow around floor deck, lumber for last two walls.
Mill after digging it out of the snow.
29. November 2012 18:18
Cabin Building Day 9
Had a local inspector looking at the project this morning when I arrived, I think he was happy with the progress so far. Suggested I upgrade to a m7 J
Back to building
Had too much taper on this one and had to cut it down so the 16" bar would cut it. Cutting another corner post.
Side wall done.
End wall done after dark.
End wall pic 2
Planning on getting the other walls done next weekend if the weather holds out.
Be sure to check back next Thursday for Part 10!
20. September 2011 17:27
FIRST-COME-FIRST-SERVED SPECIAL OFFER!
Our Paul Bunyan "Shootout" demo units will be available for sale in Cambridge, Ohio!
LUCAS PORTABLE SWING BLADE SAWMILLS - We will be bringing a 6" Lucas Mill Model 618 and a 10" Lucas Mill Model 1030 to the show. You can save in two ways. First, if you pick it up at the show you'll save on shipping and second, we're offering the 18 horse power 6" demo unit for only $11,499 ($1,000 savings off the current SALE price) and the 30 horse power 10" demo unit for only $16,999 ($2,000 savings off the current SALE price)! Just pay for the mill ahead of time and pick it up after the show on Sunday! Our operators will even give you a free quick lesson if you show up a little early. These machines only have a few hours of use - just enough time to break it in for you. There's only one each available at these prices, so if you're interested, give our Lucas Mill specialist, Doug Coughlin, a call today at 1-800-322-4539 extension 228.
As an added bonus, if you purchase one of these units you can brag to all of your friends that Stihl Timbersports World Champion, David Bolstad "broke" your mill in for you!