9. November 2012 18:35
Cabin Building Day 7
-28 today, got the mill set up for cutting logs. Made a loading ramp out of 4" timber and some stumps. Also cut a 14' long in half and place in front of the loading ramps so the logs do not get stuck to the ice during the week. Plan on hauling some logs next week and start cutting 2x4's for wall studs. Going to put 7" corner posts in each corner and two middle ones on the 20' long walls so I do not have to deal with hauling trees over 12' long.
Be sure to check back next Thursday for Part 8!
1. November 2012 22:18
Cabin Building Day 6
Hauled out the osb, only got stuck once on the trail thank god I have a warn winch on the back of my machine, its bailed me out more than once on this project. Got the rest of the floor joist and rims done, and put down the deck. Ready for some walls!
Be sure to check back next Thursday for Part 7!
25. October 2012 22:31
Cabin Building Day 5
Got the foundation all leveled up and started to put the rim joist and floor joist together. Hopefully be done with floor tomorrow.
Be sure to check back next Thursday for Part 6!
18. October 2012 22:53
Cabin Building Day 4
Worked on setting up mill on the lake and leveling out the foundation beams.
Be sure to check back next Thursday for Part 4!
11. October 2012 22:45
Cabin Building Day 3
Heat wave today, warmed up to -13. Hauled the mill up on the sled. Went very well tracked right on the trail, a person could transport the mill fully put together a long way if bolted to a wooden platform in a sled. Next step is to clear off a place on the ice to put the mill and start cutting timbers for leveling the foundation. Will tackle after the new year.
Be sure to check back next Thursday for Part 4!
4. October 2012 17:44
Cabin Building Day 2
-24 today, was able to get trees cleared and beams put in place. Going to need to haul m5 up on sled during the next couple of days. Ground is not as level as I thought, so I will need to make some 6x6 blocks to get all the foundation beams level with each other above ground. Found the highest corner and will level there up to it to avoid having to dig in the permafrost.
Be sure to check back next Thursday for Part 3!
27. September 2012 19:13
What follows is part one of a several part series that documents the true story of Mr. David Wightman of Galena, Alaska, and his ”logs to lumber” experience of building a cabin in a remote part of Alaska. The story is written in Mr. Wightman’s own words and originally appeared on the Logosol forum. We will continue to post new segments roughly once a week until the story is complete. We hope you enjoy it as much as we did!
Cabin Building Day 1
Sunday, December 26, 2010
Well after 10 years of wanting to build a cabin with an M5 in a remote location in Alaska the adventure started off today. I transported the foundation beams, sill logs, sill tops, and the floor joist that I cut with my M5 at my house to the cabin site today with a snogo and sled. Eventually when I get the foundation done and floor deck completed I will be bringing the mill out to the site for the rest of the lumber making. Here are the pics and updates for the project.
picture 1 of 8x8 beams for foundation and sill logs
picture 2 of 8x8 beams for foundation and sill logs
Bull Moose taking a look at the lumber on the way out of town. Small spike fork with a large body, would have been a good eater!
Bull and Cow moose inspecting the progress on the way out of town.
Cabin site looking in from the lake.
Cabin site looking out over the lake.
Load #2 true 2x6 floor joist cut with M5 in town, loaded and ready for a ride. 10 miles out of town one way via snogo.
Be sure to check back next Thursday for Part 2!
23. August 2012 22:42
The Arbortech TURBOPlane is a universal wood shaping blade that can be used to create different shapes, profiles and finishes. It can be used flat to create large level surfaces, or used at angles to provide shallow cuts for fine shaping, planing and sculpting. This specialized blade has Tungsten Carbide teeth for long blade life, that can easily be re-sharpened with a small diamond lapstone.
29. June 2012 00:12
Our friends at Husqvarna are offering rebates in the form of Visa gift cards with the purchase of popular chainsaws and blowers from June 8, 2012 until July 4, 2012. For a list of eligible units, click here. The rebate includes the popular Rancher line of chainsaws and handheld blowers.
19. November 2011 01:03
For years professional loggers have used this handy little filing assistant for sharpening their chains on the bar in the woods. However, not all part-time woodcutters and weekend warriors are aware of just how much help this little tool can provide when sharpening your saw chain outside of your shop or garage. Nik Bailey explains the proper use and advantages of the indispensible stump vise. After the scrench, the stump vise is probably a woodcutter's next best friend! We offer stump vises in just about every flavor (Husqvarna, Oregon, Stihl, WoodlandPRO and Carlton). Click here to take a look. But first, click PLAY...